Frequently Asked Question

WinPower Manual - 2. Software Installation & uninstall

Last Updated 5 years ago

Software running environment

System requirement

1. 256MB hard disk space at least.

2. TCP/IP protocol must be installed to support network management.

3. For local connection, an available communication port (RS-232 Serial Port or USB port) is needed to connect UPS with a communication cable.

Note: the OS should support JDK 1.7 at least, or the software won’t work normally.

Software installation

▲ Software installation must be run with administrator of system.

▲ When installing software on Windows 2008/Windows Vista/Windows 7/Windows 8/Windows 10/Windows 2012, user should right click the “setup” icon, and select the menu “Run as administrator”, there will be a dialog “user account control” pop-up, user should select “allow” button to continue installation.

Windows

On Windows, Enter \Windows, double click setup.exe to start the installation, there will be installation interface shown. Please refer to figure 2.2.1.1.

image
Figure 2.2.1.1
Click “Next” and input the Serial Number, Refer to the following figure 2.2.1.2
The Serial Number for WinPower Software is: 511C1-01220-0100-478DF2A

image
Figure 2.2.1.2
When the installation program is completed, click “Done”. Refer to the following figure 2.2.1.3
image
Figure 2.2.1.3
Linux

On Linux, copy Linux and InstallerData file, or copy LinuxAMD64 and InstallerData file, enter Linux or LinuxAMD64 file to start installation, the installation interfaces are same as section 2.2.1.

The command ./setup.bin is for GUI mode, the command ./setup_console.bin is for CUI mode.

Please note: Linux is for i386/i586/i686 Linux system, LinuxAMD64 is for x86_x64 Linux system.

Mac

On Mac OS, for Mac 10.6 or earlier OS, please enter \MacOSX file, double click the setup.zip to start the installation. For Mac 10.7 and later OS, please enter \MacOSX10.7andLater file, double click .mpkg file to start the installation.

Other OS

Copy other OS installation file and InstallerData file, enter OS file, and execute ./setup.bin for GUI mode or setup_console.bin for console mode.

For example, on AIX OS, copy AIX file and InstallerData file, Enter AIX file, execute ./setup.bin for GUI mode or setup_console.bin for CUI mode to start the installation.


Start software

Windows

Run software from Start\All Program\PowerWalker-WinPower will start the Tray and Agent. Please refer to figure 2.3.1.1.

image
Figure 2.3.1.1

There will be a green icon shown on the task bar after software starts. That means the agent is running normally. Please refer to figure 2.3.1.2.

image

Figure 2.3.1.2

“Start Agent” is to start agent; “Stop Agent” is to stop agent; “Start Monitor” is to start management interface; “Exit” is to exit agent service.

▲ On Windows 2008, Windows Vista, Windows 7, Windows 8, Windows 10 and Windows 2012, once you click “Exit”, the agent will exit, if you wants to start software again, you should restart computer, or act as an administrator to start the service “UPSmonitor” in the task manager and then start software from “start” menu, the green icon will be shown on the task bar.
image
Figure 2.3.1.3

Mac OS

The default installation path is /opt/MonitorSoftware, enter the installation path and then input the command: sudo ./agent start to start agent, input the command: sudo ./monitor to start software management interface.

Other OS

The default installation path is /opt/MonitorSoftware, enter the installation path and then input the command:./agent start to start agent, input the command: ./monitor to start software management interface.



Software uninstallation

▲ Software management interface should be closed and the agent should be exited, or else software can’t be uninstalled totally.

Windows

Close software management interface, exit software agent from “Exit” menu referring to in figure 2.3.1.2, and then uninstall software from “start” menu, please refer to figure 2.4.1.1.

Please note: user also can uninstall software from “add or remove programs” component.

  • On Windows 2008, Windows Vista, Windows 7, Windows 8 and Windows 2012, user should act as administrator when uninstalling software, select “Run as administrator” from the pop-up menu. If there is “user account control” dialog shown, please select “allow”.

image
Figure 2.4.1.1
Uninstallation interface, please refer to figure 2.4.1.2.

image
Figure 2.4.1.2
When uninstallation is finished, there will be an interface shown as figure 2.4.1.3. Please click “Done” to finish software uninstallation.

image
Figure 2.4.1.3

Mac OS

Close software management interface, enter software installation file, input command: sudo ./agent stop to stop software agent, and then input command: sudo ./Uninstall to uninstall software.

Other OS

Close software management interface, enter software installation file, input command:./agent stop to stop software agent, and then input command:./Uninstall to uninstall software.

Please Wait!

Please wait... it will take a second!